CNC bending machine programming operation

Views: 116     Author: DURMAPRESS     Publish Time: 2021-12-07      Origin: DURMAPRESS

Inquire

CNC bending machine programming operation

1. First, switch on the 2113 power supply, turn on the switch on the control panel, and then start the oil pump 5261, so that you can hear the rotation sound of the oil pump in 4102. (The machine does not move at this time)

2, stroke adjustment, use must pay attention to adjust the stroke, must be tested before bending.Its upper die down to the bottom must ensure that there is a plate thickness clearance. Otherwise it will cause damage to the mould machine. Stroke adjustment is also electric quick adjustment.

3, bending notch selection, generally choose the plate thickness of 8 times the width of the notch. For bending 4mm sheet metal, choose about 32 notches.

4, the rear stopper adjustment generally has electric quick adjustment and manual fine tuning, the method is the same as the shearing machine.

5, step on the foot switch to start bending, CNC bending machine mold and shearing machine is different, can be loosened at any time, loosen the foot will stop, continue to step down.


To see what system you use, a 2113-simple 5261 CNC as long as set cylinder stroke 4102 and rear baffle size operation can be, if you want to 1653 multi-step bending according to the operation method of different systems, respectively set the size of each step of bending, system cycle operation; If it is all digital control electro-hydraulic servo CNC bending machine will be selected for setting the lower die, the thickness of the material, material quality, length, bending mode, behind Angle and size, you can also set a variable speed according to the requirements of different point location, height of return, the holding time and deflection compensation and so on parameters of each system operation has the difference, so cannot treat as the same, hope can help to you

1. Strictly abide by the safety operation rules of machine tools, wear labor protection 4102 articles according to regulation 5261.


2. Before starting, carefully check whether the motor, 1653 switch, circuit and grounding are normal and firm, and check whether the operating parts and buttons of the equipment are stuck in the correct position.


3. Check the consistency and firmness of the upper and lower molds; Check whether the positioning device is in line with the processing requirements.


4. When the upper slide plate and each positioning axis are not in the origin state, run the back to the origin program.


5. After the equipment is started, it will run for 1-2 minutes, and the skateboard will move for 2-3 times in full journey. If there is abnormal sound or fault, it should stop immediately and remove the fault. After everything is normal, it can work.


6. Work should be unified by a unified command, so that the operator and the feeding pressing personnel closely cooperate, to ensure that the coordination personnel are in a safe position to send a bending signal.


7. The sheet must be compacted when bending to prevent the sheet from becoming warped when bending.


8. The power supply must be cut off when the plate pressing die is adjusted.


9. When changing the opening of the variable lower die, no material is allowed to contact the lower die.


10. When working, the back of the machine is not allowed to stand.


11. It is strictly forbidden to press the sheet material at one end alone.


12. When the workpiece or mold is found to be wrong during operation, it should be stopped for correction, and manual correction is strictly prohibited to prevent hand injury.


13. Do not fold super-thick iron plate or quenched steel plate, advanced alloy steel, square steel and sheet metal exceeding the performance of sheet metal bending machine, so as not to damage the machine.


14. Regularly check the overlap degree of upper and lower molds; Whether the indicator of pressure gauge is in accordance with the regulations.


15. If any abnormality occurs, stop the machine immediately, check the cause and eliminate it in time.


16. Before shutting down, place wooden blocks on the lower die under both sides of the cylinder to lower the upper slide to the wooden blocks.


17. First exit the control system program, then cut off the power supply.

How to use CNC bending machine?

CNC bending machine mold includes bracket, 2113 workbench and clamping plate, the use of 5261 wire to the coil is energized 4102, energized on the pressure plate, so as to achieve the clamping of the plate between 1653 and the base. Operation method:


1. Switch on the power supply, turn on the switch on the control panel, and then start the oil pump. (The machine does not move at this time)


2, stroke adjustment, use must pay attention to adjust the stroke, must be tested before bending.


3, bending notch selection, according to the actual situation. For example, when bending 4mm sheet metal, choose about 32 notches.


4, rear stopper adjustment generally has electric quick adjustment and manual fine tuning.


5, step on the foot switch to start bending, release the foot will stop, continue to step down.


Principle and use of CNC bending machine 2113


1. First 5261 switch on the power supply, turn on the 4102 switch on the control panel, and then start the oil pump, so that you can hear the rotation sound of the oil pump 1653. (The machine does not move at this time)


2, stroke adjustment, use must pay attention to adjust the stroke, must be tested before bending.Its upper die down to the bottom must ensure that there is a plate thickness clearance. Otherwise it will cause damage to the mould machine. Stroke adjustment is also electric quick adjustment.


3, bending notch selection, generally choose the plate thickness of 8 times the width of the notch. For bending 4mm sheet metal, choose about 32 notches.


4, CNC bending machine rear baffle adjustment generally have electric quick adjustment and manual fine tuning, the same as the shearing machine.


5, step on the foot switch to start bending, CNC bending machine mold and shearing machine is different, can be loosened at any time, loosen the foot will stop, continue to step down.


Contact Us

MENU

QUICK LINKS

CONTACT US

 0086 555 8327689

 +86 18325572889

 info@durmapress.com

FOLLOW US

二维码


SCAN  WECHAT

Copyright 2021 Maanshan Durmapress Machinery Technology Co., ltd. All rights reserved