Safe operation procedure for 3015 fiber laser cutting machine

3015 fiber laser cutting machine Safe operation procedure

1. Observe the general cutting machine safety operation rules. Start the laser in strict accordance with the laser starting procedure.

2. The operator must be trained, familiar with the structure and performance of the equipment, and master the relevant knowledge of the operating system.

3. Wear labor protective equipment according to the provisions, and wear protective glasses in accordance with the provisions near the laser beam.

4. Do not process a material until it is clear whether it can be laser irradiated or heated to avoid the potential hazard of smoke and steam.

5. When the equipment starts, the operator shall not leave the post without authorization or ask someone to take care of it. If it is necessary to leave, the operator shall stop the machine or cut off the power switch.

6. Keep the fire extinguisher within easy reach; Do not process to turn off the laser or light brake; Do not place paper, cloth or other flammable objects near unprotected laser beams.

7. If any abnormality is found in the process of processing, the machine should be shut down immediately, troubleshoot the fault or report to the supervisor in time.

8. Keep the laser, bed and the surrounding area clean, orderly and free from oil pollution, and pile up the workpiece, plate and waste materials as required.

9. When using gas cylinders, avoid crushing welding wires to avoid electric leakage accidents. The use and transportation of gas cylinders shall comply with the supervision regulations of gas cylinders. Do not burst cylinders in the sun or near heat sources. The operator must stand on the side of the bottle when opening the valve.

10. High pressure safety regulations should be observed during maintenance. Maintenance per 40 hours of operation or weekly, 1000 hours of operation or every six months shall be carried out in accordance with rules and procedures.

11. After starting the machine, manually start the machine at low speed X and Y direction to check and confirm whether there is any abnormality.

12. After the new workpiece program is input, it should be run and checked.

13. When working, pay attention to the operation of the machine tool, in order to avoid the cutting machine out of the effective range of travel or two collision caused by accidents.

Laser cutting machine a device tens of thousands of even hundreds of thousands of pieces, so in the operation must pay attention to, and usually to pay attention to maintenance and maintenance to increase the service life of equipment, cost savings, create greater benefits.

Operation protection measures

1, the necessary laser cutting machine protection equipment.

For protective equipment of laser cutting machine is a typical laser protective goggles, for prevent the laser protective goggles to the human eye injury, according to its protection principle can be divided into reflection, absorption, diffraction type and combined several, of course, they will be filtered according to the wavelength of the laser cutting machine laser radiation protection, to achieve the protection of the laser cutting machine laser on the human body, This is also a relatively safe and convenient laser cutting machine protection equipment on the market.

2, to deal with laser cutting machine radiation of their own protection.

If the human body has enough health, a little radiation for laser cutting machine can resist. So laser cutting machine operators should pay attention to eat more carrots, bean sprouts, tomatoes, lean meat, animal liver and other foods rich in vitamin A, C and protein, often drink some green tea and so on. Because these foods can help humans better protect their eyes, so that the human body can protect the human body better under the conditions of laser cutting machine radiation.

What knowledge is required

First of all, you need to know PDF graphics and learn to operate the software that comes with the machine. Software use requires the installation of software, dongle, dongle is not open software. The installation sequence is to install the data transfer port and dongle driver before installing the operating software. Software power, speed and other aspects of the adjustment. The thickness of the material varies. Thick and difficult to cut the power is large and slow, and vice versa. Power adjustment can be used on the machine operation panel to test whether the power size can cut through the material, if not, it will be good to adjust it. This is the computer side, and the machine operation panel side. There are internal control and external control, internal control is the machine itself control, external control is computer control. Use the operation software to download the PDF graphics of the cutting machine to the machine chip. Press the arrow keys on the machine operation panel to select a starting point. Then press the start of the cutting can be carried out.